IP-AL

acrylic-latex paint

2024-02-05T15:22:50+00:00

Project Description

Terrix® IP-AL
acrylic-latex paint
matt

Premium acrylic-latex topcoat paint for applying protective and decorative paint coatings inside buildings. It is especially recommended for painting walls in rooms of heavy and very heavy traffic (such as corridors, staircases, etc.) and ‘wet’ rooms (such as kitchens, bathrooms, and laundries). It is also recommended for public utility buildings, health service premises, hotels, and food industry production plants (without direct contact with food). In addition, it is intended for painting mineral substrates (such as concrete, cement renders, cement-lime renders, lime renders, and gypsum renders, as well as drywall) and those covered by coatings, topcoats based on polymers and covered with wallpapers made of glass fibres. It is used for primary and renovation painting on substrates with uniform or changeable structure and colour. Before paint application, absorbent substrates should be primed with Terrix® PR-UA or Terrix® PR-IP.

Files to download

Benefits

Main properties:

  • Extreme resistance to washing and wet scrubbing (above class I according to BS-EN 13300);
  • High resistance to water-based detergents;
  • Very low surface absorption;
  • Very good coverage;
  • High resistance to scribbling;
  • Very high resistance to dirt at the level achievable only for “ceramic” paints;
  • Suitable for very dark colours;
  • Matt finish.

Technical Data

Base binder: synthetic binder, copolymer binder;
Pigments: titanium white and inorganic and organic colour pigments;
VOC content: cat A/c. Product contains less than 30 g/l VOC;
Density: approx. 1.45 g/cm3;
Colours: white, all Terrix® chart, NCS or based on the sample provided;
Gloss level: matt;
Diluent: water;
Average consumption: approx. 0.22 l/m2 (two coats on a smooth surface);
Temperature of application (air and substrate): from +5°C to +25°C;
Relative humidity: ≤80%;
Resistance to scrubbing while wet: above class I paint according to the EN-13300 standard;
Relative diffusion resistance of 150 μm thick coating: Sd = 0.9 m (standard requirement Sd ≤2.0 m);
Surface absorption coefficient: w = 0.006 kg/m2 ⦁ h0.5 (standard requirement w ≤ 0.5 kg/ m2 ⦁ h0.5);
Packaging: single-use plastic packaging of 10 l;
Storage: the product should be stored in its original sealed packaging in a cool, dry and frost-protected room. After opening and using some of the contents, the packaging should be resealed, and the remainder of the product should be used as soon as possible;
Shelf life: 18 months from the date of production (factory-sealed packaging).

CAUTION: Keep the product out of reach of children.

Application

Substrate preparation:

The substrate must be stable (no scratches and cracks), degreased, clean, dry and free from stains and efflorescence of biological or chemical origin. In the case of microbial contamination, the substrate should be cleaned mechanically and then washed with a biocide solution to remove microbial contamination. Discolourations, nicotine stains, and efflorescence resulting from water seepage are to be initially painted with the Terrix® IP-SB stain blocker. All loose layers not connected with the surface (loose render or flaking paint coatings) are to be removed. The remnants of adhesive or lime paints must be thoroughly removed and washed with water.
New cement and limestone renders can be painted only after a two-week seasoning and gypsum-based plasters after one week. Seasoning is not required for plasterboards.
Note: If the product is being used as a part of TERRIX® render systems refer to the system manual for detailed application instructions.

Preparation:

The packaging contains a product ready for use. If necessary, the paint can be diluted with a small amount of water (adding to the first coat a maximum of 10% by volume to the second maximum of 5%). When determining the amount of water, the following should be considered: substrate type, drying conditions and application technique.

Application method:

Apply the paint to the substrate in two coats using a brush, a roller or spraying (including the “airless” method). Wait to apply the second coat of paint until the first one is completely dry, i.e. after a minimum of 3-4 hours. Use a special sheepskin fleece roller with a bristle length of min. 18 mm is recommended.

Drying:

The drying time of one coat of paint applied to the substrate (at a temperature of +20°C and relative humidity of 55%) is approximately 3 hours. Air the enclosed spaces after painting until the specific odour disappears. The coating achieves its full mechanical properties after 4 weeks.
Note: Low temperatures and high humidity extend the drying time of the paint. Protect newly applied paint from drying too fast. The coating achieves its full mechanical and functional properties after 4 weeks.

Useful hints:

Colour differences may be avoided by using a single product batch to the entire wall or element in one working cycle. Product to be applied with temperatures above +5°C. All tools are to be cleaned with water after finishing work.
Low temperatures and high air humidity may have a disadvantageous influence on the shade of the coating.

Optional add-ons:

When using paint on substrates with cracks of up to 0.3 mm in width (e.g. with fine shrinkage cracks in mineral plaster), use a microfibre-reinforced paint for the first coat is recommended (option available on request).
To increase the resistance of the paint to mould growth, it is recommended to request a special anti mould add-on (optional service).

Airless spraying:

 

Manufacturer Device Tip Pressure

(bar)

Filter

(mesh)

Dilution

(%)

Output

(l/min)

WAGNER ProSpray 3.21 0552-519 200 60 5 1.25
TITAN Titan 450e 661-519 200 60 10 1.25
GRACO

UltraMax II 795

StMax II 495

PAA621

PAA519
PAA621

170

190

60

60

5

10

3.6

2.3

Case study

Terrix PL-SX Spray Plaster

December 8th, 2022|Case study|

Terrix PL-SX Spray Plaster Ready-to-use plaster coat for machine levelling of interior walls and ceilings. ⋅ Chemically bonded product ⋅ No risk of cracking or flaking ⋅ Chemical accelerated set [...]

Related Products

Related Systems

Q&A

My name is….

My name is….

My name is….

My name is….

Go to Top